Cutting ceramic tiles using a jigsaw safely and precisely

Ceramic tiles are fragile and easily breakable. To cut through ceramic tiles, you’ll need a cutting device with an abrasive blade.

The good news is that ceramic tile can be cut safely and precisely using a jigsaw with an abrasive inorganic compound (or diamond) edge. Few other power tools can create notches, angled cuts, and openings like this one.


When cutting tile, a jigsaw should not be used as the “main cutting tool,” but rather for smaller, more intricate cuts.

Even though a jigsaw can be used to cut entire tiles, there are more efficient and cost-effective ways to complete the task. You’ll need the following for cutting ceramic tiles with a jigsaw:

Of sure you’ll like a puzzle. In this instance, it will not even be necessary to have an orbital action option, as any additional vibration will hinder the jigsaw blade rather than aid it as it attempts to cut through the ceramic tile. Visit this website for tools.

  • Blades:

Either a diamond blade or a blade composed of an abrasive inorganic compound should be utilized. Their abrasives are made from entirely different materials, and their prices are also different.

As with all jigsaw cuts, you will typically have to force yourself to mark the appropriate cutting lines.

After measuring the job’s length and width, you will appreciate your tape measures if you want to attempt square cuts. If you wish to look for curvilinear cuts over many or many tiles, you’ll additionally need a beam compass or an example.

  • Drill and Drill Bit:

You will need a drill and a glass tile or ceramic bit to create a starting hole in the tile in order to begin a cut within the interior. Additionally, you will want starting holes for the tight curves and corners of your design. Remember that the blade must be maintained and adjusted, as it is the cutting tool.

You may either keep a spray bottle on hand to periodically spritz the blade with water, or you can run a hose over the tile to add a little moisture.

Although not needed, employing a fluid enhances the longevity of the blade. You are not required to utilize a fluid if you so want.

Use extreme caution while interacting with any machinery or water nearby. It is quite dangerous! To firmly anchor the tile to an elevated surface while allowing the jigsaw blade to move up and down, you must discover the simplest approach feasible.

  • Protection:

To protect yourself from the ceramic dust released throughout the tiling process, you will be required to wear protective eyewear and a face mask.

How to Cut Straight Lines in Tile?

To cut a square or an angular shape from ceramic tile, first mark the cut line with a hand tool to serve as a guide for the cut.

It will be easier to cut larger gaps, which may span multiple tiles, if you arrange the tiles in the order they will be placed on the workstation.

On a tile of ceramic, draw lines.

To keep track of the placement and orientation of the tiles, label or grid them. Additionally, marking the waste side with an X is helpful if you’re marking multiple tiles quickly.

Install a ceramic tile-specific blade, preferably with an inorganic compound or diamond edge, on your jigsaw. These blades may safely operate on fragile materials since they grind rather than chisel the substance.

The cutting line must be hung, and the tile must be secured between two MDF or wood blocks that are firmly affixed to a workbench or sawhorse.

Ensure that the jigsaw blade has adequate area to maneuver. Turn on the jigsaw, set the speed to low, and wait for the blade to gain speed after forming the outline.

Once the jigsaw blade is prepared, carefully cut through the ceramic tile until the end of the cut is reached.

The tile is first cut using a jigsaw.

To keep the blade clean and cool throughout the entire process, keep the cut lubricated and cooled with water.

Use caution when working with water and power tools! This can also be accomplished with cutting oil, which will help keep the blade cool.

How to Make a Closed Cut with a Jigsaw in Ceramic Tile

Internal cuts are frequently made in ceramic tile to accommodate wall outlets and faucets. To attempt to make a contained tile cut, you will need a jigsaw, a bit, and an impact drill.

Clearly indicate which side of the road your blade will be cutting on by placing an “X” inside the area you wish to remove. After that, attach glass or ceramic bit to the facility drill.

Some pieces have inorganic compound-tipped ends, while others have spade-shaped cutting tips.

Below are three samples of different types of drill bits designed for drilling a pilot hole through tile, obtained from our website. Ensure that the bit can generate a large enough hole for the jigsaw blade to pass through.

Tile Carbide bit

For Tile, the still more inorganic component is required.

A diamond hole saw bit for tile

Before drilling any of the initial holes, ensure that the tile is securely in place so that it does not move when you drill. For each desired corner of the cut, drill a pilot hole within the waste section of the cutting line. Additionally, the corners of the tile are less prone to shatter due to the rounded edges of the initial holes. Utilize the jigsaw, positioning the blade within the starting hole so that it follows the cutting line when the shoe is flat against the tile. Start the device and allow the jigsaw blade to rapidly ascend.

Remove internal component

Concentrate on following the cutting line while letting the running blade do the work by easing it against the tilework.

Cutting Curvilinear Tiles: How to Do It

To cut curved lines in ceramic tile, use a shorter, dilutant inorganic compound jigsaw blade with medium or high grit.

They are also used for hard materials like marble and glass. There is really little difference between the aforementioned ways of cutting out common curves; you simply need to pay closer attention to the blade and ensure that it stays inside the cut line.

Follow the cutting line carefully, and let the fabric be removed by the abrasive grit. In order to flip tight corners, you will need to drill pilot holes.

Due to the style’s multiple steep turns, you will be required to fill in several initial gaps.

These holes can also be utilized to cut relief lines, which simplifies the creation of intricate surgical designs. If you need more guidelines, contact our experts.

Your comment submitted.

Leave a Reply.

Your phone number will not be published.